18650 battery 3.7v 2200mah

　　How to connect 18650 battery 3.7v 2200mah and manage it?

　　To connect the 18650 battery 3.7v 2200mah, you must design the connection plan in advance and tap the pole to be connected to effectively avoid the impact of incorrect connection. In addition, the management of the 18650 battery 3.7v 2200mah requires charging to ensure that the charging time is more than 12 hours. Next, I will introduce it to you Let’s look at the detailed content.

　　1. How to connect 18650 battery 3.7v 2200mah

　　1. Design the connection plan in advance. It is recommended to remove the metal accessories on hand during installation.

　　2. Before putting the 18650 battery 3.7v 2200mah on the shelf, it must be physically inspected and the open circuit voltage measured to avoid rework. When one end of the connecting cable is connected to the 18650 battery 3.7v 2200mah, the other end should be insulated and protected or held in the palm of your hand to prevent misplacement and sparking.

　　3. After one end of the cable is connected, the other end should tap the pole that needs to be connected when connecting to effectively avoid the impact of incorrect connections.

　　4. When two people are connected at the same time, there should be no connection or potential relationship between the corresponding 18650 battery 3.7v 2200mah packs. Because the two people have the same potential, if there is a potential difference between the batteries connected to each other, the battery and the two people will form a circuit, and an electric shock accident may occur.

　　5. After the 18650 battery 3.7v 2200mah pack is connected in series, the voltage between the total positive and total negative of the 18650 battery 3.7v 2200mah pack is relatively high. When connecting to the MCCB (battery switch), each wire should be connected to the MCCB first and then to the corresponding battery terminal. ; Or leave a breakpoint in the battery pack, and then connect the breakpoint after completing the connection between MCCB and 18650 battery 3.7v 2200mah pack. For multiple groups of battery packs connected in parallel, each group should have a broken end, and after connecting the MCCB terminal, use a multimeter to check the polarity and then connect the broken ends.

　　2. Management of UPS batteries

　　1. Charging for the first time. For brand-new batteries, everyone generally thinks that the overall performance is relatively good, so during the management process, they often feel that they do not pay attention to it. For the battery pack of UPS power supply, the initial charging needs to ensure that the charging time is more than 12 hours. If it is not used frequently, it must be charged before placing it. Otherwise, it will affect the function of the battery and affect the UPS. The power supply causes some damage.

　　2. Avoid excessive discharge. The life of the battery also has a certain relationship with the number of discharges, because during the use of the UPS, many staff have a certain degree of over-discharge due to lack of experience. During the discharge process of the UPS, it will also have a certain impact on the battery itself. Therefore, it is necessary to minimize the number of deep discharges. In addition, when the UPS power supply is supplying power to the battery pack, there will often be an alarm, and the alarm will last for 4-5 seconds. Based on the time and sound of this alarm, you can judge whether the power supply is normal or not, and thus whether the battery pack is in a deep discharge stage.

　　3. Maintain indoor temperature. The function of the battery is often closely related to the environment in which it is located, so the environment of the computer room will have a very direct effect on the performance of the UPS power supply. It can be seen from the corresponding requirements and regulations that the optimal temperature of UPS power supply is 25°C, the highest temperature should not exceed 40°C, and the lowest temperature should not be lower than 0°C. Generally speaking, the output capacity of the battery will often decrease due to the influence of temperature. In addition, when the temperature is too high, it will also have a certain impact on the inverter and stop running, thus causing a series of problems to the remote computer room equipment. negative effect.

　　4. Choose the appropriate charging method. At this stage, when charging UPS power supply, the constant voltage cutoff charging circuit is used by most charging systems, because the UPS itself is still a relatively sensitive system and has certain requirements for the charging voltage and current. When the charging voltage is too high or too low, it will have a certain impact on the battery pack. If the charging and discharging current value is too large, it will easily lead to deformation of the battery plates and a decrease in battery performance. Therefore, when performing actual charging, a suitable charger must be used, preferably with constant current and constant voltage functions, thereby maximizing the service life of the UPS power supply and further ensuring people's life safety. Reduce security threats.

Read recommendations:

Rack-mounted energy storage battery GN-48600-l

Is solid -state battery twice the ordinary battery?42v battery pack lithium ion direct sales

Rapid Charging Capability of Shaped Batteries

3.2v 20ah lifepo4 battery cell

3.7V Lithium Polymer Battery